Packing tips for Plasma & Flat-screen Monitors

Plasma TV displays can be difficult to ship because they are essentially two thin panels of glass with plasma, an electrically charge gas, held in suspension between them. They are delicate and relatively heavy. LCD screens, on the other hand, are lighter and less susceptible to damage, but still require careful handling.

While plasma televisions are susceptible to damage from extreme temperatures, mishandling and form operating at high altitudes, they are shipped worldwide by their manufactures without damage. the key is the packing. whenever possible, you should use the manufactures original packing container if you have retained it. If not, your mover can provide you with a special shipping container, or the unit should be packed and shipped in a container that meets the manufacture’s specifications as closely as possible.

Plasma TVs should always be shipped and stored in an upright position.Shipping the units double-boxed and upright strapped to a pallet is recommended.

If storage is involved, the requirements vary by manufacturer, but plasma TVs should be stored in a climate-controlled warehouse where the temperature does not fall below 15 degrees F or above 122 degrees F, and where the humidity does not fall below 10% or exceed 90% with no condensation. Such units should not be stored at altitudes above 9,800 feet.

Some manufactures recommend using only third-party specialists for dismounting and preparing plasma TVs for shipping, with professional installation at the destination for re-installation.

 

 

Moving with Home Electronics

A Team Moving & Storage recommend the following procedures when moving your home electronics to prevents any damage. if you take these steps before moving, your components should arrive intact.

Audio & video components

If you don’t have the owner’s manuals, or even if you do (they can often be found online).you may want to draw a diagram or take a photo of the wiring configuration to help you reconnect your components correctly after your move.  Another good tip is to put small pieces of matching colored tape on the ends of the cables and on the corresponding inputs and outputs of the components.

Remove all discs from your CD and DVD PLAYER(S) before packing to prevent scratches to your discs and damage to the laser in your player. this is also be a good time to make sure that all your discs are back in their proper cases. Some players come equipped with a “transport screw” usually located underneath the unit (check the owner’s manual). Tighten this screw before you pack your player, which will immobilize parts of the mechanism.

If your unit comes with cartridge(stacker) for multi-play remove ie before packing. the cartridge can be wrapped and packed in the same box as the  player . All trays, ehether single or multi-play, should be in the closed position before packing.

The best way to move your components is in the original boxes with the original packing. If you don’t have them, use boxes with enough room for adequate packing material. your mover can provide a sturdy packing container and materials. Packing material should snugly fill the excess room in the box so that the unit will not move around. Plastic bubble sheets make ideal packing material. Newspaper is not recommeded, as it may not securely hold the unit in place

If you have a remote control, be sure to pack it in the same box as your player. all wiring used with your player should also be packed in the same box if you have room. Seal the box with reliable packing tape. Use this packing method for packing your receiver, speakers and other audio and video components.

Some nice tips for packing your glasses/cups.

Use this step-by-step guide to pack all your glasses, goblets and cups to ensure they get to your new home in one piece.

Difficulty: Easy

Time Required: No set time

Here’s How:

1 If you can’t find a divided box, the kind used to ship bottles (wine and liquor), then use a small to medium size box and line it with bubble-wrap.

2 Place a stack of pre-cut plain newsprint on the table or other flat surface.

3 Take the first glass and place it on the pile of newsprint. Wrap two sheets of newsprint around the glass, making sure you line the inside.

4 Place the second glass inside the first one. This is called nesting. Then take two more sheets of newsprint and line the inside of the second glass. Insert another glass.

5 You can nest three or four glasses, depending on their size and weight. Lay the stack of glasses diagonally across the pile of newsprint.

6 Holding the corner of the newsprint closest to you, wrap another two sheets of newsprint around the stack and tuck in the ends.

7 For extra protection, wrap the stack in a sheet of bubblewrap and secure the ends.

8 Place glasses in bottom of box or into one of the sections if using a divided box.

9 Follow the above steps for goblets and other stemware, except for nesting. Individually wrap goblets to ensure they’re protected.

10 Once you’ve filled the box, added extra newsprint or bubble-wrap on top. Seal the box and mark it “Fragile: Glassware” and label it accordingly.

Tips:

1. Ask a wine store or specialty liquor store if they can give you some divided boxes. This will provide extra protection for your glassware.
2. Pack stacks of glasses in an individual box or place in another box with other fragiles. Just make sure the glasses are put in last on top of the other items.
3. Don’t over pack the box; however, make sure there isn’t empty space where glasses can shift about. Extra space should be filled with rolled up newspaper or bubble-wrap.

What You Need:

• Divided box or Medium size box
• Plain newsprint
• Bubblewrap
• Packing tape
• Marker/stickers